在給手機充電的時候，我們經常會混用一些充電器。在用不同的充電器進行充電時，我們也會發現手機的充電速度也會有所不同，由此我們知道，充電器是會影響手機的充電速度的。還有人認為充電器的功率越大，充電的速度也就越快，那么事實真的如此嗎?

事實是充電器功率的大小確實會影響手機的充電速度，但是它對手機充電速度的影響是被控制在一定范圍之內的。而這個充電的限額則是由手機電池的保護電路IC來決定的。比如手機的電池把電流最大限定在2A，那么你即使用多大功率的充電器，它的輸出也不會超過2A，而且如果功率過大甚至還會燒壞電池。

手機的電池不僅控制著最高的輸出，還會智能的調節充電器的充電速度。如果你仔細觀察就會發現，手機電量一般在充到80%以后，充電的速度就會慢慢的降下來，這同樣是電池的一種自我保護。

雖然充電器功率越高，不代表充電速度就越快，但是想要提高充電速度確實需要大功率的充電器。現在的快充技術流行后，手機充電器的功率也從5W漸漸變為12W、18W、22W…越來越高。弄明白可這些以后，你就知道充電器比不是功率越大越好，合適才是最重要的。